Ueevii wireless bridge for long range and connects two different locations using wireless connectivity. Ueevii wireless bridge device is useful to connect two different locations where a physical cable is not possible and wireless bridge maintenance and installation are less than wired connectivity.
Ueevii WiFi bridge also used to turn any non-wireless device into a wireless such as an IP camera, NVR, network printer, and any other device installed in a remote location and a physical cable is not possible. Ueevi wireless bridge comes with a pair of master and slave devices or also called AP and CPE devices.
There are many different wireless birge point-to-point devices available from Ueevii for different distances and speeds required. There are some popular point-to-point wireless bridges of Ueevii available as given below.
There are some wireless bridge pair for distances from 1Km to 5Km available with integrated directional antenna that are easy to mount and give you stable connectivity.
Model | Wireless Band |
UeeVii CPE880 5.8G 1Gbps Point to Point Round Wireless Bridge | 5Ghz |
UeeVii CPE850 5.8G 16dBi 5KM Gigabit Outdoor ptp | 5Ghz |
UeeVii CPE820 5.8G 1Gbps 16dBi 3KM / CPE830 | 5Ghz |
UeeVii CPE450 5.8G Outdoor CPE Point to Point Long Range / CPE453 | 5Ghz |
2.4G Wireless Bridge for 1KM Short Distance | 2.4Ghz |
Ueevii 2.4G Wireless Bridge, Point-to-Point Outdoor Internet Bridge with 12dBi Directional Antenna | 2.4Ghz |
Ueevi 5.8Ghz wireless device also comes with different model numbers so the default login IP address can be different for each device with a different web interface.
Ueevii default login username and password along with the default IP address printed to device sticker and quick user manual included with the box. Find the default login IP address and username password used for Ueevii 5.8Ghz and 2.4ghz WiFi bridge.
IP address | Username | password |
192.168.0.1 | admin | admin |
192.168.255.100 | admin | admin |
192.168.255.200 | admin | admin |
169.254.254.254 | admin | admin |
192.168.0.20 | admin | admin |
Get the default login details for your Ueevii Master and Ueevii slave device or Access point or CPE device.
A quick pairing switch is a smart way to configure the Ueevii wireless bridge using master and slave switches that are not required for the login web interface. The quick pairing method is a predefined configuration mode that auto-configures SSID and wifi password for the master device and same connects to the slave device. Configure the Wireless bridge without a PC/Laptop using the pairing switch available on both AP and CPE devices.
Power ON Master device using PoE adapter comes with the box. Use the PoE out port to the Master Device LAN port and wait to power on it for about 2 minutes.
There are small switches with M and S options. To make the device Mast switch should be near M and for the Slave modem Switch should be S side.
Now Press the tiny reset button until you get a channel on the LEE screen. The LED screen will show a,b,c…f and 1,2,3. check CH0011 C mean channel number and 11 is 11 number channel for 2.4Ghz and CH0036.
Now connect device B with the PoE adapter and power on it. Wait for 2 minutes until it’s properly powered ON.
Now repeater the same process is done for the Master device and select the same channel as selected on the Master device. Exp- if the Master device LED shows CH0036 make the same channel on Slave device and wait until the device connects and you will see the signal LED status show solid green.
In configuring a Wireless bridge two Wireless devices need to be configured one by one. One device wireless mode configures as an Access point or Access point WDS and the second device Mode should be client or CPE mode. Follow the steps to configure the Ueevii Wireless bridge Point to point or point to multipoint for long range.
Tplinklogin Admin Login User Guide
Connect the second device to set up as client mode from browser settings.
Use the PoE adapter and connect the same as connect for the device connection steps and access with the default login IP address and password.
Go to Lan settings first and change the Slave IP address to different than the Master IP. Use the same series but as both devices same default login IP change for slave and login again.
Change Wireless Operation mode first.
Go to “Bridge Set”
Bridge- Slave B
Save settings and go to the wireless option tab.
You will get a “SCAN” button beside the SSID option.
Scan for the Master device and you will get the SSID name you configured in the Master device.
Select the SSID and provide a wireless security key configured in the Master device.
Save settings and wait until the Slave device connects to the Master device.
After the wireless connection is established with the slave device from the master device both device signal LED lights will be solid green and the wireless bridge ready to use.
To get high throughput wireless connectivity in wireless bridge point-to-point or point-to-multipoint connectivity you need proper placement of both master and slave device. There are a few points that you should keep in mind while installing a point-to-point long-range link.
192.168.200.1 Login Router Admin Password 192.168.200.1 C class IP address used as default login IP…
Arris G36 Vs Netgear Cax80 Review, Price and Troubleshooting It's very hard to pick the…
How to Solve if Eero Blinking White? Eero is a mesh whole home Wi-Fi system…
Dual Wan Router For Home and Office Best Multi WAN router in 2024 to use…
AC750 Vs Ac1200 Which one is Best? You probably see AC750 and Ac1200 while thinking…
How To Reset Hughesnet Router if Forgotten Login Password? Resetting a Modem or router is…